Common Bearing Failures: Causes, Symptoms and Corrective Actions
Bearing failures can result from improper installation, inadequate lubrication, excessive loads, contamination, misalignment, electrical current, or unsuitable operating conditions. Identifying the appearance of a failure can help determine its possible cause and the appropriate corrective action.
The table below summarizes common bearing failures, their typical appearance, possible causes, and recommended corrective actions.
← Swipe to view full table
| Bearing Problem | Appearance | Possible Causes | Corrective Actions |
|---|---|---|---|
| Flaking | Flaking occurs on the raceway or rolling element surface, producing a clearly uneven surface. |
• Excessive load or improper operating conditions • Improper installation • Poor accuracy of the shaft or housing • Insufficient internal clearance • Foreign matter entering the bearing • Rust or corrosion • Reduced hardness due to abnormally high temperature |
• Review the operating conditions • Re-select the bearing if necessary • Reconsider the internal clearance • Check the machining accuracy of the shaft and housing • Review the surrounding bearing design • Check the installation method • Check the lubricant and lubrication method |
| Seizure / Burn | The bearing becomes overheated and discolored, followed by seizure or burning, and eventually cannot rotate. |
• Insufficient internal clearance, including clearance reduced by deformation • Insufficient lubrication or unsuitable lubricant • Excessive load, such as excessive preload • Roller skewing |
• Adjust and set an appropriate internal clearance; increase it if necessary • Check the lubricant type and ensure an adequate quantity is supplied • Check the operating conditions • Prevent installation misalignment • Check the surrounding bearing design, including heat transfer to the bearing • Improve the bearing assembly method |
| Cracks | Defects, local chipping, or cracks appear in the rings or rolling elements. |
• Excessive impact load • Excessive interference fit • Severe flaking • Cracking caused by frictional heat, often due to inadequate lubrication • Poor accuracy at the mounting location, such as an excessive fillet radius • Improper handling or use, such as striking with a copper hammer or allowing large foreign matter to become trapped |
• Check the operating conditions • Set an appropriate interference fit and check the material • Improve installation and operating methods • Improve lubrication to prevent frictional heat and friction cracks • Check the surrounding bearing design |
| Cage Damage | Rivets become loose or break; the cage becomes cracked or fractured. |
• Excessive moment load • High-speed rotation or frequent speed changes • Inadequate lubrication • Foreign matter becoming trapped • Excessive vibration • Improper installation, such as installation in a misaligned condition • Abnormal temperature rise in resin cages |
• Check the operating conditions • Check the lubrication conditions • Reconsider the cage selection • Improve installation and operating conditions to prevent impact, misalignment, and abnormal temperature rise • Review the rigidity of the shaft and housing |
| Scuffing / Smearing | The surface becomes rough and shows small areas of adhesion. Scuffing between the ring flange and roller end face may also occur. |
• Inadequate lubrication • Foreign matter entering the bearing • Roller skewing caused by bearing misalignment • Excessive axial load causing the oil film on the flange surface to break down • Excessive surface roughness • Excessive sliding of the rolling elements |
• Review the lubricant and lubrication method • Check the operating conditions • Set an appropriate preload • Improve the sealing performance • Avoid abnormal axial loads and improve installation accuracy and lubrication |
| Rust / Corrosion | Local or overall rust appears on the surface; rust may appear in a pattern corresponding to the rolling element spacing. |
• Improper storage conditions • Improper packaging • Insufficient rust preventive protection • Ingress of water, acidic solutions, or other corrosive substances • Handling the bearing directly with bare hands |
• Improve storage conditions to prevent rust during storage • Improve sealing performance • Regularly check the lubricant and rust-prevention condition • Avoid direct contact with bare hands; wear gloves and handle bearings properly |
| Fretting Wear | Reddish-brown wear particles are generated on the mating surfaces. |
• Insufficient interference fit • Small oscillation angle or small amplitude of oscillatory motion • Insufficient lubrication or operation without lubrication • Unstable load • Vibration during transportation |
• Check the interference fit and lubricant application condition • During transportation, package the inner and outer rings separately; if they cannot be separated, apply preload • Re-select the lubricant • Re-select the bearing |
| Wear | Surface wear causes dimensional changes and is often accompanied by scoring or wear marks. |
• Foreign matter mixed into the lubricant • Inadequate lubrication • Roller skewing |
• Check the lubricant and lubrication method • Improve sealing performance • Prevent alignment errors |
| Electrical Erosion | Spark-like pits appear on the raceway and may further develop into a corrugated or fluted pattern. | • Electric current passes through the bearing, causing current flow through the rolling contact |
• Provide a bypass path for the electrical current, such as a grounding brush • Use insulation measures to prevent current from passing through the bearing |
| Indentation / Denting | Dents or indentations are produced when solid foreign matter becomes trapped or by impact. Scratches may also occur during installation. |
• Solid foreign matter entering the bearing • Flaking particles or metal debris becoming trapped • Impact or dropping caused by improper installation • Installation in a misaligned condition |
• Improve installation and operating methods • Prevent foreign matter from entering the bearing • If caused by metal debris, inspect other parts of the bearing and equipment |
| Creep | Sliding occurs on the inner or outer diameter surface, producing a mirror-like surface or discoloration; seizure may sometimes occur. |
• Insufficient interference fit at the mating surface • Insufficient sleeve tightening • Abnormal temperature rise • Excessive load |
• Reconsider the interference fit • Review the operating conditions • Check the accuracy of the shaft and housing |
Need Help Identifying a Bearing Problem?
Share the bearing type, operating conditions, and observed symptoms with our team.