Common Bearing Failures: Causes, Symptoms and Corrective Actions

Bearing failures can result from improper installation, inadequate lubrication, excessive loads, contamination, misalignment, electrical current, or unsuitable operating conditions. Identifying the appearance of a failure can help determine its possible cause and the appropriate corrective action.

The table below summarizes common bearing failures, their typical appearance, possible causes, and recommended corrective actions.

← Swipe to view full table

Bearing Problem Appearance Possible Causes Corrective Actions
Flaking Flaking occurs on the raceway or rolling element surface, producing a clearly uneven surface. • Excessive load or improper operating conditions
• Improper installation
• Poor accuracy of the shaft or housing
• Insufficient internal clearance
• Foreign matter entering the bearing
• Rust or corrosion
• Reduced hardness due to abnormally high temperature
• Review the operating conditions
• Re-select the bearing if necessary
• Reconsider the internal clearance
• Check the machining accuracy of the shaft and housing
• Review the surrounding bearing design
• Check the installation method
• Check the lubricant and lubrication method
Seizure / Burn The bearing becomes overheated and discolored, followed by seizure or burning, and eventually cannot rotate. • Insufficient internal clearance, including clearance reduced by deformation
• Insufficient lubrication or unsuitable lubricant
• Excessive load, such as excessive preload
• Roller skewing
• Adjust and set an appropriate internal clearance; increase it if necessary
• Check the lubricant type and ensure an adequate quantity is supplied
• Check the operating conditions
• Prevent installation misalignment
• Check the surrounding bearing design, including heat transfer to the bearing
• Improve the bearing assembly method
Cracks Defects, local chipping, or cracks appear in the rings or rolling elements. • Excessive impact load
• Excessive interference fit
• Severe flaking
• Cracking caused by frictional heat, often due to inadequate lubrication
• Poor accuracy at the mounting location, such as an excessive fillet radius
• Improper handling or use, such as striking with a copper hammer or allowing large foreign matter to become trapped
• Check the operating conditions
• Set an appropriate interference fit and check the material
• Improve installation and operating methods
• Improve lubrication to prevent frictional heat and friction cracks
• Check the surrounding bearing design
Cage Damage Rivets become loose or break; the cage becomes cracked or fractured. • Excessive moment load
• High-speed rotation or frequent speed changes
• Inadequate lubrication
• Foreign matter becoming trapped
• Excessive vibration
• Improper installation, such as installation in a misaligned condition
• Abnormal temperature rise in resin cages
• Check the operating conditions
• Check the lubrication conditions
• Reconsider the cage selection
• Improve installation and operating conditions to prevent impact, misalignment, and abnormal temperature rise
• Review the rigidity of the shaft and housing
Scuffing / Smearing The surface becomes rough and shows small areas of adhesion. Scuffing between the ring flange and roller end face may also occur. • Inadequate lubrication
• Foreign matter entering the bearing
• Roller skewing caused by bearing misalignment
• Excessive axial load causing the oil film on the flange surface to break down
• Excessive surface roughness
• Excessive sliding of the rolling elements
• Review the lubricant and lubrication method
• Check the operating conditions
• Set an appropriate preload
• Improve the sealing performance
• Avoid abnormal axial loads and improve installation accuracy and lubrication
Rust / Corrosion Local or overall rust appears on the surface; rust may appear in a pattern corresponding to the rolling element spacing. • Improper storage conditions
• Improper packaging
• Insufficient rust preventive protection
• Ingress of water, acidic solutions, or other corrosive substances
• Handling the bearing directly with bare hands
• Improve storage conditions to prevent rust during storage
• Improve sealing performance
• Regularly check the lubricant and rust-prevention condition
• Avoid direct contact with bare hands; wear gloves and handle bearings properly
Fretting Wear Reddish-brown wear particles are generated on the mating surfaces. • Insufficient interference fit
• Small oscillation angle or small amplitude of oscillatory motion
• Insufficient lubrication or operation without lubrication
• Unstable load
• Vibration during transportation
• Check the interference fit and lubricant application condition
• During transportation, package the inner and outer rings separately; if they cannot be separated, apply preload
• Re-select the lubricant
• Re-select the bearing
Wear Surface wear causes dimensional changes and is often accompanied by scoring or wear marks. • Foreign matter mixed into the lubricant
• Inadequate lubrication
• Roller skewing
• Check the lubricant and lubrication method
• Improve sealing performance
• Prevent alignment errors
Electrical Erosion Spark-like pits appear on the raceway and may further develop into a corrugated or fluted pattern. • Electric current passes through the bearing, causing current flow through the rolling contact • Provide a bypass path for the electrical current, such as a grounding brush
• Use insulation measures to prevent current from passing through the bearing
Indentation / Denting Dents or indentations are produced when solid foreign matter becomes trapped or by impact. Scratches may also occur during installation. • Solid foreign matter entering the bearing
• Flaking particles or metal debris becoming trapped
• Impact or dropping caused by improper installation
• Installation in a misaligned condition
• Improve installation and operating methods
• Prevent foreign matter from entering the bearing
• If caused by metal debris, inspect other parts of the bearing and equipment
Creep Sliding occurs on the inner or outer diameter surface, producing a mirror-like surface or discoloration; seizure may sometimes occur. • Insufficient interference fit at the mating surface
• Insufficient sleeve tightening
• Abnormal temperature rise
• Excessive load
• Reconsider the interference fit
• Review the operating conditions
• Check the accuracy of the shaft and housing

Need Help Identifying a Bearing Problem?

Share the bearing type, operating conditions, and observed symptoms with our team.

Describe the Bearing Problem →